Technical data:
Functions: start, stop, speed: 33 1/3 & 45, limit switch, repeate, up-lifter, locate
Drive: Servo controlled direct drive
RPM Deviation: <0.002%
Wow and flutter: < 0.010%warmth
Rumble to noise ratio: 78 db (DIN B)
Platter: Die-cast aluminum, 310 mm
Tonearm: eff. Length: 220 mm, design: straight, dynamically balanced
Needle overhang: 16mm adjustable
adjustable support weight: 0 - 3 g
System carrier: PCL-40
Frequency range: 20Hz - 50kHz
recommended Bearing weight: 16 ± 3mN
Special equipment:
Microprocessor-controlled contactless "Dynamic Servo Tracer" tonearm with Q-damping
high speed constancy due to the quartz-controlled tachogenerator principle
Revision type standard:
The circuit boards and contact points are cleaned and photoresistors are replaced. Adjustment / control of the setting for the starting point (30/17), limit switch, applied weight, function test and test run. VDE safety test.
Housing:
The original case has been expertly restored and redesigned with multiple coats of colored paint. The subsequently applied high-gloss paint gives the case a noble appearance. The connection panel for all required cable connections is located on the back and four height-adjustable spikes made of chrome-plated stainless steel are installed in the bottom of the housing.
Pickup:
MM cartridge Ortofon Vinyl Master Alpha
With the VM series, Ortofon has long created the reference MM pickup, the long production time and the characteristic stylus body are well known all over the world. The Vinyl Master Alpha (identical to VM White) is the entry into the series and is a super entry-level system for mid-range turntables.
The VM series from Ortofon is compatible with each other. So you can start with a VM Alpha and then improve the quality with the appropriate needle slot by using the next needle slot.
Audio cable:
brand cable. Ready-made analog audio cinch cable for wiring turntables! Thanks to the particularly high-quality inner conductor made of oxygen-free copper (OFC), this quality cable ensures natural signal transmission. Contact security and protection against corrosion is guaranteed by the 24 carat gold-plated plug contacts. The cable has a neutral sound with good dynamics and spatiality.
Plate weight:
Made of degaussed stainless steel. With a weight of 310g, it ensures that the record lies flat on the platter and runs smoothly. This record weight plays in the "middle" weight class. It adds just enough weight to dampen plate vibration without stressing the bushings. By using it, you increase the sound performance of your system.
Operating voltage:
We ship the Denon DP-47F to all countries worldwide. The voltage is changed by an internal transformer, optionally with 100 to 240 volts. The country-specific power cord is also supplied to match.
OPTIONAL (with SURCHARGE)
Upgrade pickup:
Ortofon
Audio technica
New housing:
The case is made of 16mm MDF and consists of two separate parts, the case frame and the case back. More stability, more weight, less vibration! The connection panel for all required cable connections is located on the back. 4 threaded sockets are embedded on the floor for a variable installation of different device foot variants.
Device feet made of stainless steel:
Height adjustable. The contact surface to the substructure is reduced to a minimum by three embedded rubber buffers. Resonance and feedback are thus effectively prevented. Perfect surface, total weight 2520g, diameter 65mm, height without cushioning rubber 25mm, height with cushioning rubber 26mm
Hood and Hinges:
High-quality acrylic hood, wall thickness 4mm, material Plexiglas XT (cast and extruded), transparency absolutely colorless and clear, robustness unbreakable to impact-resistant, unrivaled weather and Resistant to aging with a 10-year material guarantee, high-quality surface and flatness, glossy
Original hinges in mint condition.
Full revision:
Replacement of all electrolytic capacitors (37 pieces) on main u. Motor circuit board by high quality from Panasonic. Boards and contact points cleaned, replacement of the photo resistors. Adjustment / control of the setting for the starting point (30/17), limit switch, applied weight, function test and test run. VDE safety test.
